Difference between revisions of "FreeBSD fiber channel target"
(→References) |
|||
(5 intermediate revisions by the same user not shown) | |||
Line 1: | Line 1: | ||
+ | [[Category:FreeBSD]] | ||
+ | |||
== Introduction == | == Introduction == | ||
Line 22: | Line 24: | ||
== Check the WWN address == | == Check the WWN address == | ||
− | |||
− | |||
You'll get output like: | You'll get output like: | ||
Line 37: | Line 37: | ||
== Configure /etc/ctl.conf == | == Configure /etc/ctl.conf == | ||
− | Use this | + | Use this config for /etc/ctl.conf: |
− | target naa. | + | lun fibre-channel { |
+ | backend block | ||
+ | device-id "5000c5001d5ba30b" | ||
+ | serial "MGKSERIAL0001" | ||
+ | option vendor "MGK" | ||
+ | option product "FC Disk" | ||
+ | option naa "600A0B80002682A8000067D95897A544" | ||
+ | option removable "on" | ||
+ | path /dev/zvol/tank1/export/fc | ||
+ | } | ||
+ | |||
+ | target naa.100000062b1b88c8 { | ||
auth-group no-authentication | auth-group no-authentication | ||
− | port | + | port mpt0 |
− | port | + | port mpt1 |
− | lun 0 | + | lun 0 fibre-channel |
− | |||
− | |||
− | |||
} | } | ||
− | Make sure the WWN matches. Next, start the ctld daemon. | + | Make sure the WWN matches. Next, start the ctld daemon. The device-id is from a real Seagate FC disk, and the naa is from a real array. I think both are required by macOS to make multipathing work. |
sudo service ctld start | sudo service ctld start | ||
Line 63: | Line 71: | ||
ctld_name=naa.2100001b321cd5b6,lun,0 | ctld_name=naa.2100001b321cd5b6,lun,0 | ||
scsiname=naa.2100001b321cd5b6,lun,0 | scsiname=naa.2100001b321cd5b6,lun,0 | ||
+ | |||
+ | == Initiator side == | ||
+ | |||
+ | If using macOS, the mac should just "see" the target, no configuration required. | ||
== References == | == References == |
Latest revision as of 10:25, 22 February 2019
Contents
Introduction
You need:
- FreeBSD with a kernel that supports your card, e.g. for QLogic QLE2462
- a fiber channel card that supports target mode
- a ZFS zvol
Create a ZFS zvol
This will create a sparse 850GB ZFS zvol.
sudo zfs create -p -s -V 850g tank1/export/fc
Enable ctld
sudo sysrc ctld_enable=YES
Bring the device online
sudo ctladm port -o on isp0 sudo ctladm port -o on isp1
Check the WWN address
You'll get output like:
z800:aram$ sudo ctladm port -l Port Online Frontend Name pp vp 0 YES camsim camsim 0 0 naa.50000009e370df01 1 YES ioctl ioctl 0 0 2 YES tpc tpc 0 0 3 YES camtgt isp0 0 0 naa.2100001b321cd5b6 4 YES camtgt isp1 0 0 naa.2101001b323cd5b6
Configure /etc/ctl.conf
Use this config for /etc/ctl.conf:
lun fibre-channel { backend block device-id "5000c5001d5ba30b" serial "MGKSERIAL0001" option vendor "MGK" option product "FC Disk" option naa "600A0B80002682A8000067D95897A544" option removable "on" path /dev/zvol/tank1/export/fc } target naa.100000062b1b88c8 { auth-group no-authentication port mpt0 port mpt1 lun 0 fibre-channel }
Make sure the WWN matches. Next, start the ctld daemon. The device-id is from a real Seagate FC disk, and the naa is from a real array. I think both are required by macOS to make multipathing work.
sudo service ctld start
Query the status, to see if everything is working correctly:
z800:aram$ sudo ctladm devlist -v LUN Backend Size (Blocks) BS Serial Number Device ID 0 block 1782579200 512 MYSERIAL 0 MYDEVID 0 lun_type=0 num_threads=14 file=/dev/zvol/tank1/export/fc ctld_name=naa.2100001b321cd5b6,lun,0 scsiname=naa.2100001b321cd5b6,lun,0
Initiator side
If using macOS, the mac should just "see" the target, no configuration required.